ELCT/Simba-OmniInfantry
9
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

refactor(modules): 按角色重排 modules/ 目录,消除命名不一致

Browse Source 
原 modules/ 下目录大小写混用(BMI088/BUZZER/DR16/IST8310/LED/PID 为大写,
attitude/c_comm/filter/gimbal/ins/motor/referee/shoot 为小写),且把第三方
移植代码(QuaternionEKF/kalman_filter)与本工程封装(ins)混在同一目录。

新结构(全部小写,按角色分层,第三方代码单独隔离):

  modules/
    algorithm/   pid.c/h  filter.c/h          通用算法
    imu/         attitude.c/h  ins.c/h        姿态与惯导封装
    imu/qekf/    QuaternionEKF.c/h  kalman_filter.c/h
                                              (移植自 Wang Hongxi INS 例程)
    sensor/      bmi088.c/h  ist8310.c/h      板载传感器驱动
    comms/       dr16.c/h  c_comm.c/h  referee.c/h
    motor/       dji_motor.c/h                电机抽象
    control/     gimbal.c/h  shoot.c/h        整车控制逻辑
                 (底盘为 chassis.c/h)
    dev/         led.c/h  buzzer.c/h          板级指示/发声

共移动 58 个文件(每板 29 个),旧目录全部删除。

工程文件同步(每个工程各 2 个):
- .uvprojx: Modules 分组 16 个 <FilePath> 改为新路径;
  2 个非空 <IncludePath> 元素:15 个旧模块路径收敛为 8 个新目录,
  并顺带删除陈旧项 ../modules/AHRS(目录根本不存在,legacy 时代残留)
  与冗余项 ..\bsp(与 ../Bsp/Inc 重复)
- .uvoptx: 16 个 <PathWithFileName> 同步

关于"为什么不用改源码": Keil 的 include 靠 IncludePath 解析,本工程所有
#include 都是纯文件名形式(无路径限定),所以移动目录只需改工程配置。
另外 .h 完全不登记在工程里(只有 16 个 .c 被登记),故头文件只需移动。

回归验证(无法在此环境编译,用等价判据):
- 两个工程引用的 98 / 95 个 <FilePath> 全部真实存在
- 磁盘上 47 / 45 个 .c 全部仍被工程引用 —— 即没有任何文件掉出编译
- 2 个 IncludePath 元素均含全部 8 个新模块目录,无旧路径残留
- 所有 IncludePath 指向的目录均真实存在
- .uvprojx/.uvoptx XML 良构
- 两棵树结构一致(chassis/gimbal 等板级差异符合预期)

⚠️ 仍需在 Keil 里点一次编译确认(见 README 的构建章节)。
This commit is contained in:
LSMushui
2026-09-12 11:51:41 +08:00
parent 3e5e5e3f95
commit e3d432f3b5
62 changed files with 62 additions and 62 deletions
Download Patch File Download Diff File Expand all files Collapse all files
云台/modules/imu/attitude.c
+54
View File
@@ -0,0 +1,54 @@
/* =============================================================================
* attitude.c - 姿态解算封装(BMI088 + QuaternionEKF 惯导)
* 2026-08-31 起由 Mahony 互补滤波更换为 Wang Hongxi 的 QuaternionEKF:
* - 陀螺零偏在线估计,不再需要上电静止校准(1s 阻塞校准已移除)
* - 卡方检验剔除加速度异常帧,动态响应/抗震动干扰优于互补滤波
* - 欧拉角映射(与旧 Mahony get_yaw/pitch/roll 语义一一对应,勿改):
* att_deg_yaw <- QEKF_INS.Yaw (标准偏航;取多圈累计 YawTotalAngle)
* att_deg_roll <- QEKF_INS.Pitch (绕 x 轴;本云台 Pitch 环反馈用它)
* att_deg_pitch <- QEKF_INS.Roll (绕 y 轴)
* 原因:QEKF 内部变量命名与航空惯例互换,见 ins.c 文件头
* 数据链: bmi088.c(SPI DMA 后台更新) -> ins_update(1kHz) -> att_deg_*
* 健康位: bmi088_online=0 时姿态数据不可用(云台任务会拒绝输出);
* 姿态收敛需数秒,上电初期 ConvergeFlag=0 属正常
* ========================================================================== */
#include "attitude.h"
#include "bmi088.h"
#include "ist8310.h"
#include "ins.h"
#include "tim.h"
extern TIM_HandleTypeDef htim10;
float att_deg_yaw; // 多圈连续偏航角(°)
float att_deg_pitch; // 绕 y 轴角(°)
float att_deg_roll; // 绕 x 轴角(°,本云台 Pitch 环反馈)
uint8_t att_ready = 0; // 1-标定完成且姿态已开始输出(控制任务门控用)
void attitude_init(void)
{
ist8310_init();
bmi088_init();
ins_init();
}
void attitude_update(void)
{
/* 先做数据路健康检查:IMU 数据一旦冻结,姿态会安静地"保持不动"甚至
* 匀速漂移(见 bmi088.c 的 bmi088_health_check 说明) */
bmi088_health_check();
ins_update(0.001f); // 1kHz 固定节拍
att_deg_yaw = INS.YawTotalAngle; // 多圈连续角,云台 Yaw 环直接使用
att_deg_roll = INS.Pitch; // QEKF 命名互换,见文件头
att_deg_pitch = INS.Roll;
if (INS.UpdateCount > 0)
att_ready = 1;
}
void imu_heater_off(void)
{
__HAL_TIM_SET_COMPARE(&htim10, TIM_CHANNEL_1, 0);
}
云台/modules/imu/attitude.h
+28
View File
@@ -0,0 +1,28 @@
#ifndef ATTITUDE_H
#define ATTITUDE_H
/* 姿态解算封装(BMI088 + QuaternionEKF 惯导 + 多圈 Yaw)
* 2026-08-31 由 Mahony 更换为 QuaternionEKF(见 attitude.c 文件头)
* 注意:本云台的 Pitch 环反馈使用 att_deg_roll(绕 x 轴角,安装方向所致),
* 而 att_deg_roll 映射自 QEKF_INS.Pitch(QEKF 命名与航空惯例互换) */
#include <stdint.h>
extern float att_deg_yaw; // 多圈连续偏航角(°)
extern float att_deg_pitch; // 绕 y 轴角(°)
extern float att_deg_roll; // 绕 x 轴角(°,本云台 Pitch 环反馈)
/* 初始化:配置 IST8310/BMI088(阻塞,有界重试)+ z 轴静止零偏标定(约 1s,
* 车体必须静止;QEKF 不估计 z 偏置)+ QuaternionEKF 初值 */
extern void attitude_init(void);
/* 姿态更新(1kHz 调用,dt=0.001s) */
extern void attitude_update(void);
/* 1-z 轴标定完成且姿态已有效输出(标定期间姿态为 0,控制任务须门控) */
extern uint8_t att_ready;
/* IMU 加热器(TIM10 CH1/PF6 PWM):monitor 检测到过温时调用强制关闭 */
extern void imu_heater_off(void);
#endif
云台/modules/imu/ins.c
+198
View File
@@ -0,0 +1,198 @@
/* =============================================================================
* ins.c - 惯导姿态解算封装实现(见 ins.h 说明)
* 移植自 RoboMaster-C-Board-INS-Example-master 的 ins_task.c:
* - 去除 BMI088driver/controller/bsp_PWM/bsp_dwt 依赖,数据源改为本工程
* 的 bmi088 驱动全局量,温度控制仍由 IMU_Task 负责
* - dt 由调用方传入(IMU_Task 固定 1ms),不再使用 DWT 计时
* - 保留运动加速度解算(低通 0.0085),供后续功能扩展(如功率/跌倒检测)
* 欧拉角约定(重要):
* QEKF 内部变量命名与航空惯例互换——QEKF_INS.Pitch 是绕 x 轴的角,
* QEKF_INS.Roll 是绕 y 轴的角;attitude.c 按"本工程 Pitch 反馈=QEKF.Pitch"
* 映射(与旧 Mahony 方案的 get_roll 语义一致),勿凭名字想当然
* ========================================================================== */
#include "ins.h"
#include "QuaternionEKF.h"
#include "bmi088.h"
#include "main.h"
#include <string.h>
/* ---- z 轴静止零偏标定 ----
* QEKF 无法观测 z 偏置(见 ins.h),只能上电静止标定。
* 2026-09-12 加健壮性:原来直接对前 1000 个样本取均值,而 BMI088 刚初始化
* 完时 SPI DMA 还没稳定,且上电瞬间车体往往正被摆弄 —— 一旦标定窗口里混入
* 运动样本,gyro_z_offset 就被污染成一个偏大的常值,表现为**上电后 yaw 以
* 恒定角速度自漂**(实测 -3.85°/s,而原始 |gyro| 仅 0.017rad/s,量级对不上
* 才发现是零偏而非陀螺本身)。现在:
* 1. 先等采样路稳定(INS_Z_CAL_SETTLE_MS)
* 2. 单样本 |gyro| 超过 INS_Z_CAL_MAX_G 视为无效(静止时不该出现)
* 3. 一轮内有效样本占比不足 INS_Z_CAL_MIN_QUIET 视为"上电时车体在动",
* 整轮作废重测,最多 INS_Z_CAL_ATTEMPTS 轮
* 4. 多轮都不静则用最后一轮的均值并置 ins_z_cal_ok=0(有补偿总好过没有,
* 但是否可信由该标志告诉调用方/调试者)
* 单轮只取 0.5s:LED_Task 的 IWDG 上电宽限期是 5s,而 IMU_Task 在
* attitude_init() 期间不刷新心跳,所以整个初始化必须留在 5s 内 —— 可靠
* 性靠"整轮作废重测"而不是靠拉长单轮,3 轮最坏 1.55s,仅比原来的 1s 略长 */
#define INS_Z_CAL_SETTLE_MS 50
#define INS_Z_CAL_SAMPLES 500
#define INS_Z_CAL_MAX_G 0.35f /* rad/s,约 20°/s */
#define INS_Z_CAL_MIN_QUIET 0.9f
#define INS_Z_CAL_ATTEMPTS 3
static float gyro_z_offset = 0;
static uint8_t z_cal_done = 0;
float ins_gyro_z_offset = 0; /* 诊断用,见 ins.h */
uint8_t ins_z_cal_ok = 0; /* 诊断用,见 ins.h */
INS_t INS;
static const float xb[3] = {1, 0, 0};
static const float yb[3] = {0, 1, 0};
static const float zb[3] = {0, 0, 1};
void ins_init(void)
{
memset(&INS, 0, sizeof(INS));
/* 等 SPI 采样路稳定,避免把未就绪/残留的样本算进零偏 */
HAL_Delay(INS_Z_CAL_SETTLE_MS);
/* z 轴静止零偏标定(见文件头;x/y 偏置由 EKF 在线估计,无需校准)。
* 标定期间 ins_update() 不输出,控制任务由 ins_ready() 门控 */
for (uint8_t attempt = 0; attempt < INS_Z_CAL_ATTEMPTS; attempt++)
{
float sum = 0;
uint16_t valid = 0;
for (uint16_t i = 0; i < INS_Z_CAL_SAMPLES; i++)
{
const float gx = bmi088_gyro[0];
const float gy = bmi088_gyro[1];
const float gz = bmi088_gyro[2];
if (gx * gx + gy * gy + gz * gz <= INS_Z_CAL_MAX_G * INS_Z_CAL_MAX_G)
{
sum += gz;
valid++;
}
HAL_Delay(1);
}
if (valid > 0)
gyro_z_offset = sum / (float)valid;
if ((float)valid >= INS_Z_CAL_MIN_QUIET * (float)INS_Z_CAL_SAMPLES)
{
ins_z_cal_ok = 1; /* 整轮都静止,零偏可信 */
break;
}
/* 否则认为上电时车体在动,整轮作废、再来一轮 */
}
ins_gyro_z_offset = gyro_z_offset;
z_cal_done = 1;
INS.Initialized = 1;
/* 与 INS 例程 demo 相同的参数组合:
* 过程噪声1=10(四元数) 过程噪声2=0.001(零偏) 观测噪声=1e7(加速度)
* 渐消因子=1(不渐消) 加速度低通=0(内部另有运动加速度低通) */
IMU_QuaternionEKF_Init(10, 0.001f, 10000000, 1, 0);
}
uint8_t ins_ready(void)
{
return z_cal_done;
}
void ins_update(float dt)
{
if (!z_cal_done)
return;
/* BMI088 驱动在 SPI DMA 完成回调中后台更新,这里直接取最新值;
* z 轴减去上电标定的零偏(x/y 由 EKF 在线估计,不再静态校准) */
float gyro[3] = {bmi088_gyro[0], bmi088_gyro[1],
bmi088_gyro[2] - gyro_z_offset};
float accel[3] = {bmi088_accel[0], bmi088_accel[1], bmi088_accel[2]};
/* 核心函数,EKF 更新四元数(内部含零偏估计与卡方检验) */
IMU_QuaternionEKF_Update(gyro[0], gyro[1], gyro[2],
accel[0], accel[1], accel[2], dt);
memcpy(INS.q, QEKF_INS.q, sizeof(INS.q));
/* 机体系基向量转换到导航系(惯性系=导航系),供扩展功能使用 */
float xn[3], yn[3], zn[3];
BodyFrameToEarthFrame(xb, xn, INS.q);
BodyFrameToEarthFrame(yb, yn, INS.q);
BodyFrameToEarthFrame(zb, zn, INS.q);
/* 将重力从导航系转到机体系,计算运动加速度(低通),供扩展使用 */
const float gravity[3] = {0, 0, 9.81f};
float gravity_b[3];
EarthFrameToBodyFrame(gravity, gravity_b, INS.q);
const float AccelLPF = 0.0085f;
for (uint8_t i = 0; i < 3; i++)
{
INS.MotionAccel_b[i] = (accel[i] - gravity_b[i]) * dt / (AccelLPF + dt) +
INS.MotionAccel_b[i] * AccelLPF / (AccelLPF + dt);
}
/* 获取最终数据(QEKF 内部已含多圈 Yaw 处理) */
INS.Yaw = QEKF_INS.Yaw;
INS.Pitch = QEKF_INS.Pitch;
INS.Roll = QEKF_INS.Roll;
INS.YawTotalAngle = QEKF_INS.YawTotalAngle;
INS.GyroBias[0] = QEKF_INS.GyroBias[0];
INS.GyroBias[1] = QEKF_INS.GyroBias[1];
INS.GyroBias[2] = QEKF_INS.GyroBias[2];
INS.StableFlag = QEKF_INS.StableFlag;
INS.ConvergeFlag = QEKF_INS.ConvergeFlag;
INS.ChiSquare = QEKF_INS.ChiSquare_Data[0];
INS.UpdateCount = QEKF_INS.UpdateCount;
(void)xn;
(void)yn;
(void)zn;
(void)zb;
}
/**
* @brief Transform 3dvector from BodyFrame to EarthFrame
* @param[1] vector in BodyFrame
* @param[2] vector in EarthFrame
* @param[3] quaternion
*/
void BodyFrameToEarthFrame(const float *vecBF, float *vecEF, float *q)
{
vecEF[0] = 2.0f * ((0.5f - q[2] * q[2] - q[3] * q[3]) * vecBF[0] +
(q[1] * q[2] - q[0] * q[3]) * vecBF[1] +
(q[1] * q[3] + q[0] * q[2]) * vecBF[2]);
vecEF[1] = 2.0f * ((q[1] * q[2] + q[0] * q[3]) * vecBF[0] +
(0.5f - q[1] * q[1] - q[3] * q[3]) * vecBF[1] +
(q[2] * q[3] - q[0] * q[1]) * vecBF[2]);
vecEF[2] = 2.0f * ((q[1] * q[3] - q[0] * q[2]) * vecBF[0] +
(q[2] * q[3] + q[0] * q[1]) * vecBF[1] +
(0.5f - q[1] * q[1] - q[2] * q[2]) * vecBF[2]);
}
/**
* @brief Transform 3dvector from EarthFrame to BodyFrame
* @param[1] vector in EarthFrame
* @param[2] vector in BodyFrame
* @param[3] quaternion
*/
void EarthFrameToBodyFrame(const float *vecEF, float *vecBF, float *q)
{
vecBF[0] = 2.0f * ((0.5f - q[2] * q[2] - q[3] * q[3]) * vecEF[0] +
(q[1] * q[2] + q[0] * q[3]) * vecEF[1] +
(q[1] * q[3] - q[0] * q[2]) * vecEF[2]);
vecBF[1] = 2.0f * ((q[1] * q[2] - q[0] * q[3]) * vecEF[0] +
(0.5f - q[1] * q[1] - q[3] * q[3]) * vecEF[1] +
(q[2] * q[3] + q[0] * q[1]) * vecEF[2]);
vecBF[2] = 2.0f * ((q[1] * q[3] + q[0] * q[2]) * vecEF[0] +
(q[2] * q[3] - q[0] * q[1]) * vecEF[1] +
(0.5f - q[1] * q[1] - q[2] * q[2]) * vecEF[2]);
}
云台/modules/imu/ins.h
+62
View File
@@ -0,0 +1,62 @@
/* =============================================================================
* ins.h - 惯导姿态解算封装(移植自 RoboMaster-C-Board-INS-Example, Wang Hongxi)
* 核心: QuaternionEKF 四元数 EKF——陀螺积分预测 + 加速度重力方向观测,
* 在线估计 x/y 陀螺零偏,卡方检验剔除加速度异常(撞击/运动)帧
* 对比旧 Mahony 方案: 收敛更快、零偏在线估计(无需上电静止校准)、
* 动态加速度干扰抑制更好(卡方检验)
* 数据源: 本工程 BMI088 驱动的 bmi088_accel/gyro(SPI DMA 后台更新)
* 调用: ins_init() 一次,ins_update(dt) 每 1ms;dt 用固定 0.001
* (IMU_Task 为 vTaskDelayUntil 精确 1kHz 节拍,无需 DWT 计时)
* ========================================================================== */
#ifndef INS_H
#define INS_H
#include <stdint.h>
typedef struct
{
uint8_t Initialized;
float Gyro[3]; // rad/s(零偏修正后)
float Accel[3]; // m/s^2
float q[4]; // 四元数 w x y z
float Yaw; // -180~180(°)
float Pitch; // QEKF 命名(实际为绕 x 轴角,本工程映射见 attitude.c)
float Roll; // 同上
float YawTotalAngle; // 多圈连续 Yaw(°)
float GyroBias[3]; // EKF 在线估计的陀螺零偏(rad/s)
float MotionAccel_b[3]; // 运动加速度(机体系,去除重力,低通)
uint8_t StableFlag; // 1-载体静止且加速度正常(可用于 ZUPT 等扩展)
uint8_t ConvergeFlag; // 1-卡方检验收敛(姿态可信)
float ChiSquare; // 最近一次卡方检验值(诊断用)
uint32_t UpdateCount; // 更新计数(诊断用)
} INS_t;
extern INS_t INS;
/* 初始化:先做 z 轴静止零偏标定(约 1s 阻塞,车体必须静止——QEKF 的
* 卡方观测无法感知 z 偏置,GyroBias[2] 恒为 0,不标定会导致 Yaw 持续漂移),
* 再初始化 EKF(参数为 INS 例程 demo 值,调参见 QuaternionEKF.c 头注释) */
extern void ins_init(void);
/* 姿态更新(1kHz 调用,dt 单位秒;内部读 bmi088_accel/gyro 全局量)
* 标定完成前直接返回,不更新 */
extern void ins_update(float dt);
/* 1-标定完成且已有有效姿态输出(控制任务以此为门控) */
extern uint8_t ins_ready(void);
/* ---- z 轴零偏标定的诊断量(见 ins.c 文件头) ----
* 姿态异常时先看这两个量和 debug_task 的 gz/cvg 是否自洽:
* 若 gyro_z_offset 明显偏离静止时的真实零偏,yaw 会以 -(offset) 的恒定
* 角速度自漂,与陀螺原始输出无关 */
extern float ins_gyro_z_offset; // 实际采用的 z 零偏(rad/s)
extern uint8_t ins_z_cal_ok; // 1-标定时车体静止,零偏可信;0-始终在动
/* 坐标系变换工具(机体系 <-> 导航系) */
extern void BodyFrameToEarthFrame(const float *vecBF, float *vecEF, float *q);
extern void EarthFrameToBodyFrame(const float *vecEF, float *vecBF, float *q);
#endif
云台/modules/imu/qekf/QuaternionEKF.c
+492
View File
@@ -0,0 +1,492 @@
/**
******************************************************************************
* @file QuaternionEKF.c
* @author Wang Hongxi
* @version V1.2.0
* @date 2022/3/8
* @brief attitude update with gyro bias estimate and chi-square test
******************************************************************************
* @attention
* 1st order LPF transfer function:
* 1
* ———————
* as + 1
******************************************************************************
*/
#include "QuaternionEKF.h"
QEKF_INS_t QEKF_INS;
const float IMU_QuaternionEKF_F[36] = {1, 0, 0, 0, 0, 0,
0, 1, 0, 0, 0, 0,
0, 0, 1, 0, 0, 0,
0, 0, 0, 1, 0, 0,
0, 0, 0, 0, 1, 0,
0, 0, 0, 0, 0, 1};
float IMU_QuaternionEKF_P[36] = {100000, 0.1, 0.1, 0.1, 0.1, 0.1,
0.1, 100000, 0.1, 0.1, 0.1, 0.1,
0.1, 0.1, 100000, 0.1, 0.1, 0.1,
0.1, 0.1, 0.1, 100000, 0.1, 0.1,
0.1, 0.1, 0.1, 0.1, 100, 0.1,
0.1, 0.1, 0.1, 0.1, 0.1, 100};
float IMU_QuaternionEKF_K[18];
float IMU_QuaternionEKF_H[18];
static float invSqrt(float x);
static void IMU_QuaternionEKF_Observe(KalmanFilter_t *kf);
static void IMU_QuaternionEKF_F_Linearization_P_Fading(KalmanFilter_t *kf);
static void IMU_QuaternionEKF_SetH(KalmanFilter_t *kf);
static void IMU_QuaternionEKF_xhatUpdate(KalmanFilter_t *kf);
/**
* @brief Quaternion EKF initialization and some reference value
* @param[in] process_noise1 quaternion process noise 10
* @param[in] process_noise2 gyro bias process noise 0.001
* @param[in] measure_noise accel measure noise 1000000
* @param[in] lambda fading coefficient 0.9996
* @param[in] lpf lowpass filter coefficient 0
*/
void IMU_QuaternionEKF_Init(float process_noise1, float process_noise2, float measure_noise, float lambda, float lpf)
{
QEKF_INS.Initialized = 1;
QEKF_INS.Q1 = process_noise1;
QEKF_INS.Q2 = process_noise2;
QEKF_INS.R = measure_noise;
QEKF_INS.ChiSquareTestThreshold = 1e-8;
QEKF_INS.ConvergeFlag = 0;
QEKF_INS.ErrorCount = 0;
QEKF_INS.UpdateCount = 0;
if (lambda > 1)
{
lambda = 1;
}
QEKF_INS.lambda = lambda;
QEKF_INS.accLPFcoef = lpf;
// 初始化矩阵维度信息
Kalman_Filter_Init(&QEKF_INS.IMU_QuaternionEKF, 6, 0, 3);
Matrix_Init(&QEKF_INS.ChiSquare, 1, 1, (float *)QEKF_INS.ChiSquare_Data);
// 姿态初始化
QEKF_INS.IMU_QuaternionEKF.xhat_data[0] = 1;
QEKF_INS.IMU_QuaternionEKF.xhat_data[1] = 0;
QEKF_INS.IMU_QuaternionEKF.xhat_data[2] = 0;
QEKF_INS.IMU_QuaternionEKF.xhat_data[3] = 0;
// 自定义函数初始化,用于扩展或增加kf的基础功能
QEKF_INS.IMU_QuaternionEKF.User_Func0_f = IMU_QuaternionEKF_Observe;
QEKF_INS.IMU_QuaternionEKF.User_Func1_f = IMU_QuaternionEKF_F_Linearization_P_Fading;
QEKF_INS.IMU_QuaternionEKF.User_Func2_f = IMU_QuaternionEKF_SetH;
QEKF_INS.IMU_QuaternionEKF.User_Func3_f = IMU_QuaternionEKF_xhatUpdate;
// 设定标志位,用自定函数替换kf标准步骤中的SetK(计算增益)以及xhatupdate(后验估计/融合)
QEKF_INS.IMU_QuaternionEKF.SkipEq3 = TRUE;
QEKF_INS.IMU_QuaternionEKF.SkipEq4 = TRUE;
memcpy(QEKF_INS.IMU_QuaternionEKF.F_data, IMU_QuaternionEKF_F, sizeof(IMU_QuaternionEKF_F));
memcpy(QEKF_INS.IMU_QuaternionEKF.P_data, IMU_QuaternionEKF_P, sizeof(IMU_QuaternionEKF_P));
}
/**
* @brief Quaternion EKF update
* @param[in] gyro x y z in rad/s
* @param[in] accel x y z in m/s²
* @param[in] update period in s
*/
void IMU_QuaternionEKF_Update(float gx, float gy, float gz, float ax, float ay, float az, float dt)
{
// 0.5(Ohm-Ohm^bias)*deltaT,用于更新工作点处的状态转移F矩阵
static float halfgxdt, halfgydt, halfgzdt;
static float accelInvNorm;
if (!QEKF_INS.Initialized)
{
IMU_QuaternionEKF_Init(10, 0.001, 1000000 * 10, 0.9996 * 0 + 1, 0);
}
/* F, number with * represent vals to be set
0 1* 2* 3* 4 5
6* 7 8* 9* 10 11
12* 13* 14 15* 16 17
18* 19* 20* 21 22 23
24 25 26 27 28 29
30 31 32 33 34 35
*/
QEKF_INS.dt = dt;
QEKF_INS.Gyro[0] = gx - QEKF_INS.GyroBias[0];
QEKF_INS.Gyro[1] = gy - QEKF_INS.GyroBias[1];
QEKF_INS.Gyro[2] = gz - QEKF_INS.GyroBias[2];
// set F
halfgxdt = 0.5f * QEKF_INS.Gyro[0] * dt;
halfgydt = 0.5f * QEKF_INS.Gyro[1] * dt;
halfgzdt = 0.5f * QEKF_INS.Gyro[2] * dt;
// 此部分设定状态转移矩阵F的左上角部分 4x4子矩阵,即0.5(Ohm-Ohm^bias)*deltaT,右下角有一个2x2单位阵已经初始化好了
// 注意在predict步F的右上角是4x2的零矩阵,因此每次predict的时候都会调用memcpy用单位阵覆盖前一轮线性化后的矩阵
memcpy(QEKF_INS.IMU_QuaternionEKF.F_data, IMU_QuaternionEKF_F, sizeof(IMU_QuaternionEKF_F));
QEKF_INS.IMU_QuaternionEKF.F_data[1] = -halfgxdt;
QEKF_INS.IMU_QuaternionEKF.F_data[2] = -halfgydt;
QEKF_INS.IMU_QuaternionEKF.F_data[3] = -halfgzdt;
QEKF_INS.IMU_QuaternionEKF.F_data[6] = halfgxdt;
QEKF_INS.IMU_QuaternionEKF.F_data[8] = halfgzdt;
QEKF_INS.IMU_QuaternionEKF.F_data[9] = -halfgydt;
QEKF_INS.IMU_QuaternionEKF.F_data[12] = halfgydt;
QEKF_INS.IMU_QuaternionEKF.F_data[13] = -halfgzdt;
QEKF_INS.IMU_QuaternionEKF.F_data[15] = halfgxdt;
QEKF_INS.IMU_QuaternionEKF.F_data[18] = halfgzdt;
QEKF_INS.IMU_QuaternionEKF.F_data[19] = halfgydt;
QEKF_INS.IMU_QuaternionEKF.F_data[20] = -halfgxdt;
// accel low pass filter,加速度过一下低通滤波平滑数据,降低撞击和异常的影响
if (QEKF_INS.UpdateCount == 0) // 如果是第一次进入,需要初始化低通滤波
{
QEKF_INS.Accel[0] = ax;
QEKF_INS.Accel[1] = ay;
QEKF_INS.Accel[2] = az;
}
QEKF_INS.Accel[0] = QEKF_INS.Accel[0] * QEKF_INS.accLPFcoef / (QEKF_INS.dt + QEKF_INS.accLPFcoef) + ax * QEKF_INS.dt / (QEKF_INS.dt + QEKF_INS.accLPFcoef);
QEKF_INS.Accel[1] = QEKF_INS.Accel[1] * QEKF_INS.accLPFcoef / (QEKF_INS.dt + QEKF_INS.accLPFcoef) + ay * QEKF_INS.dt / (QEKF_INS.dt + QEKF_INS.accLPFcoef);
QEKF_INS.Accel[2] = QEKF_INS.Accel[2] * QEKF_INS.accLPFcoef / (QEKF_INS.dt + QEKF_INS.accLPFcoef) + az * QEKF_INS.dt / (QEKF_INS.dt + QEKF_INS.accLPFcoef);
// set z,单位化重力加速度向量
accelInvNorm = invSqrt(QEKF_INS.Accel[0] * QEKF_INS.Accel[0] + QEKF_INS.Accel[1] * QEKF_INS.Accel[1] + QEKF_INS.Accel[2] * QEKF_INS.Accel[2]);
for (uint8_t i = 0; i < 3; i++)
{
QEKF_INS.IMU_QuaternionEKF.MeasuredVector[i] = QEKF_INS.Accel[i] * accelInvNorm; // 用加速度向量更新量测值
}
// get body state
QEKF_INS.gyro_norm = 1.0f / invSqrt(QEKF_INS.Gyro[0] * QEKF_INS.Gyro[0] +
QEKF_INS.Gyro[1] * QEKF_INS.Gyro[1] +
QEKF_INS.Gyro[2] * QEKF_INS.Gyro[2]);
QEKF_INS.accl_norm = 1.0f / accelInvNorm;
// 如果角速度小于阈值且加速度处于设定范围内,认为运动稳定,加速度可以用于修正角速度
// 稍后在最后的姿态更新部分会利用StableFlag来确定
if (QEKF_INS.gyro_norm < 0.3f && QEKF_INS.accl_norm > 9.8f - 0.5f && QEKF_INS.accl_norm < 9.8f + 0.5f)
{
QEKF_INS.StableFlag = 1;
}
else
{
QEKF_INS.StableFlag = 0;
}
// set Q R,过程噪声和观测噪声矩阵
QEKF_INS.IMU_QuaternionEKF.Q_data[0] = QEKF_INS.Q1 * QEKF_INS.dt;
QEKF_INS.IMU_QuaternionEKF.Q_data[7] = QEKF_INS.Q1 * QEKF_INS.dt;
QEKF_INS.IMU_QuaternionEKF.Q_data[14] = QEKF_INS.Q1 * QEKF_INS.dt;
QEKF_INS.IMU_QuaternionEKF.Q_data[21] = QEKF_INS.Q1 * QEKF_INS.dt;
QEKF_INS.IMU_QuaternionEKF.Q_data[28] = QEKF_INS.Q2 * QEKF_INS.dt;
QEKF_INS.IMU_QuaternionEKF.Q_data[35] = QEKF_INS.Q2 * QEKF_INS.dt;
QEKF_INS.IMU_QuaternionEKF.R_data[0] = QEKF_INS.R;
QEKF_INS.IMU_QuaternionEKF.R_data[4] = QEKF_INS.R;
QEKF_INS.IMU_QuaternionEKF.R_data[8] = QEKF_INS.R;
// 调用kalman_filter.c封装好的函数,注意几个User_Funcx_f的调用
Kalman_Filter_Update(&QEKF_INS.IMU_QuaternionEKF);
// 获取融合后的数据,包括四元数和xy零飘值
QEKF_INS.q[0] = QEKF_INS.IMU_QuaternionEKF.FilteredValue[0];
QEKF_INS.q[1] = QEKF_INS.IMU_QuaternionEKF.FilteredValue[1];
QEKF_INS.q[2] = QEKF_INS.IMU_QuaternionEKF.FilteredValue[2];
QEKF_INS.q[3] = QEKF_INS.IMU_QuaternionEKF.FilteredValue[3];
QEKF_INS.GyroBias[0] = QEKF_INS.IMU_QuaternionEKF.FilteredValue[4];
QEKF_INS.GyroBias[1] = QEKF_INS.IMU_QuaternionEKF.FilteredValue[5];
QEKF_INS.GyroBias[2] = 0; // 大部分时候z轴通天,无法观测yaw的漂移
// 利用四元数反解欧拉角
QEKF_INS.Yaw = atan2f(2.0f * (QEKF_INS.q[0] * QEKF_INS.q[3] + QEKF_INS.q[1] * QEKF_INS.q[2]), 2.0f * (QEKF_INS.q[0] * QEKF_INS.q[0] + QEKF_INS.q[1] * QEKF_INS.q[1]) - 1.0f) * 57.295779513f;
QEKF_INS.Pitch = atan2f(2.0f * (QEKF_INS.q[0] * QEKF_INS.q[1] + QEKF_INS.q[2] * QEKF_INS.q[3]), 2.0f * (QEKF_INS.q[0] * QEKF_INS.q[0] + QEKF_INS.q[3] * QEKF_INS.q[3]) - 1.0f) * 57.295779513f;
QEKF_INS.Roll = asinf(-2.0f * (QEKF_INS.q[1] * QEKF_INS.q[3] - QEKF_INS.q[0] * QEKF_INS.q[2])) * 57.295779513f;
// get Yaw total, yaw数据可能会超过360,处理一下方便其他功能使用(如小陀螺)
if (QEKF_INS.Yaw - QEKF_INS.YawAngleLast > 180.0f)
{
QEKF_INS.YawRoundCount--;
}
else if (QEKF_INS.Yaw - QEKF_INS.YawAngleLast < -180.0f)
{
QEKF_INS.YawRoundCount++;
}
QEKF_INS.YawTotalAngle = 360.0f * QEKF_INS.YawRoundCount + QEKF_INS.Yaw;
QEKF_INS.YawAngleLast = QEKF_INS.Yaw;
QEKF_INS.UpdateCount++; // 初始化低通滤波用,计数测试用
}
/**
* @brief 用于更新线性化后的状态转移矩阵F右上角的一个4x2分块矩阵,稍后用于协方差矩阵P的更新;
* 并对零漂的方差进行限制,防止过度收敛并限幅防止发散
*
* @param kf
*/
static void IMU_QuaternionEKF_F_Linearization_P_Fading(KalmanFilter_t *kf)
{
static float q0, q1, q2, q3;
static float qInvNorm;
q0 = kf->xhatminus_data[0];
q1 = kf->xhatminus_data[1];
q2 = kf->xhatminus_data[2];
q3 = kf->xhatminus_data[3];
// quaternion normalize
qInvNorm = invSqrt(q0 * q0 + q1 * q1 + q2 * q2 + q3 * q3);
for (uint8_t i = 0; i < 4; i++)
{
kf->xhatminus_data[i] *= qInvNorm;
}
/* F, number with * represent vals to be set
0 1 2 3 4* 5*
6 7 8 9 10* 11*
12 13 14 15 16* 17*
18 19 20 21 22* 23*
24 25 26 27 28 29
30 31 32 33 34 35
*/
// set F
kf->F_data[4] = q1 * QEKF_INS.dt / 2;
kf->F_data[5] = q2 * QEKF_INS.dt / 2;
kf->F_data[10] = -q0 * QEKF_INS.dt / 2;
kf->F_data[11] = q3 * QEKF_INS.dt / 2;
kf->F_data[16] = -q3 * QEKF_INS.dt / 2;
kf->F_data[17] = -q0 * QEKF_INS.dt / 2;
kf->F_data[22] = q2 * QEKF_INS.dt / 2;
kf->F_data[23] = -q1 * QEKF_INS.dt / 2;
// fading filter,防止零飘参数过度收敛
kf->P_data[28] /= QEKF_INS.lambda;
kf->P_data[35] /= QEKF_INS.lambda;
// 限幅,防止发散
if (kf->P_data[28] > 10000)
{
kf->P_data[28] = 10000;
}
if (kf->P_data[35] > 10000)
{
kf->P_data[35] = 10000;
}
}
/**
* @brief 在工作点处计算观测函数h(x)的Jacobi矩阵H
*
* @param kf
*/
static void IMU_QuaternionEKF_SetH(KalmanFilter_t *kf)
{
static float doubleq0, doubleq1, doubleq2, doubleq3;
/* H
0 1 2 3 4 5
6 7 8 9 10 11
12 13 14 15 16 17
last two cols are zero
*/
// set H
doubleq0 = 2 * kf->xhatminus_data[0];
doubleq1 = 2 * kf->xhatminus_data[1];
doubleq2 = 2 * kf->xhatminus_data[2];
doubleq3 = 2 * kf->xhatminus_data[3];
memset(kf->H_data, 0, sizeof_float * kf->zSize * kf->xhatSize);
kf->H_data[0] = -doubleq2;
kf->H_data[1] = doubleq3;
kf->H_data[2] = -doubleq0;
kf->H_data[3] = doubleq1;
kf->H_data[6] = doubleq1;
kf->H_data[7] = doubleq0;
kf->H_data[8] = doubleq3;
kf->H_data[9] = doubleq2;
kf->H_data[12] = doubleq0;
kf->H_data[13] = -doubleq1;
kf->H_data[14] = -doubleq2;
kf->H_data[15] = doubleq3;
}
/**
* @brief 利用观测值和先验估计得到最优的后验估计
* 加入了卡方检验以判断融合加速度的条件是否满足
* 同时引入发散保护保证恶劣工况下的必要量测更新
*
* @param kf
*/
static void IMU_QuaternionEKF_xhatUpdate(KalmanFilter_t *kf)
{
static float q0, q1, q2, q3;
kf->MatStatus = Matrix_Transpose(&kf->H, &kf->HT); // z|x => x|z
kf->temp_matrix.numRows = kf->H.numRows;
kf->temp_matrix.numCols = kf->Pminus.numCols;
kf->MatStatus = Matrix_Multiply(&kf->H, &kf->Pminus, &kf->temp_matrix); // temp_matrix = H·P'(k)
kf->temp_matrix1.numRows = kf->temp_matrix.numRows;
kf->temp_matrix1.numCols = kf->HT.numCols;
kf->MatStatus = Matrix_Multiply(&kf->temp_matrix, &kf->HT, &kf->temp_matrix1); // temp_matrix1 = H·P'(k)·HT
kf->S.numRows = kf->R.numRows;
kf->S.numCols = kf->R.numCols;
kf->MatStatus = Matrix_Add(&kf->temp_matrix1, &kf->R, &kf->S); // S = H P'(k) HT + R
kf->MatStatus = Matrix_Inverse(&kf->S, &kf->temp_matrix1); // temp_matrix1 = inv(H·P'(k)·HT + R)
q0 = kf->xhatminus_data[0];
q1 = kf->xhatminus_data[1];
q2 = kf->xhatminus_data[2];
q3 = kf->xhatminus_data[3];
kf->temp_vector.numRows = kf->H.numRows;
kf->temp_vector.numCols = 1;
// 计算预测得到的重力加速度方向(通过姿态获取的)
kf->temp_vector_data[0] = 2 * (q1 * q3 - q0 * q2);
kf->temp_vector_data[1] = 2 * (q0 * q1 + q2 * q3);
kf->temp_vector_data[2] = q0 * q0 - q1 * q1 - q2 * q2 + q3 * q3; // temp_vector = h(xhat'(k))
// 计算预测值和各个轴的方向余弦
for (uint8_t i = 0; i < 3; i++)
{
QEKF_INS.OrientationCosine[i] = acosf(fabsf(kf->temp_vector_data[i]));
}
// 利用加速度计数据修正
kf->temp_vector1.numRows = kf->z.numRows;
kf->temp_vector1.numCols = 1;
kf->MatStatus = Matrix_Subtract(&kf->z, &kf->temp_vector, &kf->temp_vector1); // temp_vector1 = z(k) - h(xhat'(k))
// chi-square test,卡方检验
kf->temp_matrix.numRows = kf->temp_vector1.numRows;
kf->temp_matrix.numCols = 1;
kf->MatStatus = Matrix_Multiply(&kf->temp_matrix1, &kf->temp_vector1, &kf->temp_matrix); // temp_matrix = inv(H·P'(k)·HT + R)·(z(k) - h(xhat'(k)))
kf->temp_vector.numRows = 1;
kf->temp_vector.numCols = kf->temp_vector1.numRows;
kf->MatStatus = Matrix_Transpose(&kf->temp_vector1, &kf->temp_vector); // temp_vector = z(k) - h(xhat'(k))'
kf->MatStatus = Matrix_Multiply(&kf->temp_vector, &kf->temp_matrix, &QEKF_INS.ChiSquare);
// rk is small,filter converged/converging
if (QEKF_INS.ChiSquare_Data[0] < 0.5f * QEKF_INS.ChiSquareTestThreshold)
{
QEKF_INS.ConvergeFlag = 1;
}
// rk is bigger than thre but once converged
if (QEKF_INS.ChiSquare_Data[0] > QEKF_INS.ChiSquareTestThreshold && QEKF_INS.ConvergeFlag)
{
if (QEKF_INS.StableFlag)
{
QEKF_INS.ErrorCount++; // 载体静止时仍无法通过卡方检验
}
else
{
QEKF_INS.ErrorCount = 0;
}
if (QEKF_INS.ErrorCount > 50)
{
// 滤波器发散
QEKF_INS.ConvergeFlag = 0;
kf->SkipEq5 = FALSE; // step-5 is cov mat P updating
}
else
{
// 残差未通过卡方检验 仅预测
// xhat(k) = xhat'(k)
// P(k) = P'(k)
memcpy(kf->xhat_data, kf->xhatminus_data, sizeof_float * kf->xhatSize);
memcpy(kf->P_data, kf->Pminus_data, sizeof_float * kf->xhatSize * kf->xhatSize);
kf->SkipEq5 = TRUE; // part5 is P updating
return;
}
}
else // if divergent or rk is not that big/acceptable,use adaptive gain
{
// scale adaptive,rk越小则增益越大,否则更相信预测值
if (QEKF_INS.ChiSquare_Data[0] > 0.1f * QEKF_INS.ChiSquareTestThreshold && QEKF_INS.ConvergeFlag)
{
QEKF_INS.AdaptiveGainScale = (QEKF_INS.ChiSquareTestThreshold - QEKF_INS.ChiSquare_Data[0]) / (0.9f * QEKF_INS.ChiSquareTestThreshold);
}
else
{
QEKF_INS.AdaptiveGainScale = 1;
}
QEKF_INS.ErrorCount = 0;
kf->SkipEq5 = FALSE;
}
// cal kf-gain K
kf->temp_matrix.numRows = kf->Pminus.numRows;
kf->temp_matrix.numCols = kf->HT.numCols;
kf->MatStatus = Matrix_Multiply(&kf->Pminus, &kf->HT, &kf->temp_matrix); // temp_matrix = P'(k)·HT
kf->MatStatus = Matrix_Multiply(&kf->temp_matrix, &kf->temp_matrix1, &kf->K);
// implement adaptive
for (uint8_t i = 0; i < kf->K.numRows * kf->K.numCols; i++)
{
kf->K_data[i] *= QEKF_INS.AdaptiveGainScale;
}
for (uint8_t i = 4; i < 6; i++)
{
for (uint8_t j = 0; j < 3; j++)
{
kf->K_data[i * 3 + j] *= QEKF_INS.OrientationCosine[i - 4] / 1.5707963f; // 1 rad
}
}
kf->temp_vector.numRows = kf->K.numRows;
kf->temp_vector.numCols = 1;
kf->MatStatus = Matrix_Multiply(&kf->K, &kf->temp_vector1, &kf->temp_vector); // temp_vector = K(k)·(z(k) - H·xhat'(k))
// 零漂修正限幅,一般不会有过大的漂移
if (QEKF_INS.ConvergeFlag)
{
for (uint8_t i = 4; i < 6; i++)
{
if (kf->temp_vector.pData[i] > 1e-2f * QEKF_INS.dt)
{
kf->temp_vector.pData[i] = 1e-2f * QEKF_INS.dt;
}
if (kf->temp_vector.pData[i] < -1e-2f * QEKF_INS.dt)
{
kf->temp_vector.pData[i] = -1e-2f * QEKF_INS.dt;
}
}
}
// 不修正yaw轴数据
kf->temp_vector.pData[3] = 0;
kf->MatStatus = Matrix_Add(&kf->xhatminus, &kf->temp_vector, &kf->xhat);
}
/**
* @brief EKF观测环节,其实就是把数据复制一下
*
* @param kf kf类型定义
*/
static void IMU_QuaternionEKF_Observe(KalmanFilter_t *kf)
{
memcpy(IMU_QuaternionEKF_P, kf->P_data, sizeof(IMU_QuaternionEKF_P));
memcpy(IMU_QuaternionEKF_K, kf->K_data, sizeof(IMU_QuaternionEKF_K));
memcpy(IMU_QuaternionEKF_H, kf->H_data, sizeof(IMU_QuaternionEKF_H));
}
/**
* @brief 自定义1/sqrt(x),速度更快
*
* @param x x
* @return float
*/
static float invSqrt(float x)
{
float halfx = 0.5f * x;
float y = x;
long i = *(long *)&y;
i = 0x5f375a86 - (i >> 1);
y = *(float *)&i;
y = y * (1.5f - (halfx * y * y));
return y;
}
云台/modules/imu/qekf/QuaternionEKF.h
+75
View File
@@ -0,0 +1,75 @@
/**
******************************************************************************
* @file QuaternionEKF.h
* @author Wang Hongxi
* @version V1.2.0
* @date 2022/3/8
* @brief attitude update with gyro bias estimate and chi-square test
******************************************************************************
* @attention
*
******************************************************************************
*/
#ifndef _QUAT_EKF_H
#define _QUAT_EKF_H
#include "kalman_filter.h"
/* boolean type definitions */
#ifndef TRUE
#define TRUE 1 /**< boolean true */
#endif
#ifndef FALSE
#define FALSE 0 /**< boolean fails */
#endif
typedef struct
{
uint8_t Initialized;
KalmanFilter_t IMU_QuaternionEKF;
uint8_t ConvergeFlag;
uint8_t StableFlag;
uint64_t ErrorCount;
uint64_t UpdateCount;
float q[4]; // 四元数估计值
float GyroBias[3]; // 陀螺仪零偏估计值
float Gyro[3];
float Accel[3];
float OrientationCosine[3];
float accLPFcoef;
float gyro_norm;
float accl_norm;
float AdaptiveGainScale;
float Roll;
float Pitch;
float Yaw;
float YawTotalAngle;
float Q1; // 四元数更新过程噪声
float Q2; // 陀螺仪零偏过程噪声
float R; // 加速度计量测噪声
float dt; // 姿态更新周期
mat ChiSquare;
float ChiSquare_Data[1]; // 卡方检验检测函数
float ChiSquareTestThreshold; // 卡方检验阈值
float lambda; // 渐消因子
int16_t YawRoundCount;
float YawAngleLast;
} QEKF_INS_t;
extern QEKF_INS_t QEKF_INS;
extern float chiSquare;
extern float ChiSquareTestThreshold;
void IMU_QuaternionEKF_Init(float process_noise1, float process_noise2, float measure_noise, float lambda, float lpf);
void IMU_QuaternionEKF_Update(float gx, float gy, float gz, float ax, float ay, float az, float dt);
#endif
云台/modules/imu/qekf/kalman_filter.c
+480
View File
@@ -0,0 +1,480 @@
/**
******************************************************************************
* @file kalman filter.c
* @author Wang Hongxi
* @version V1.2.2
* @date 2022/1/8
* @brief C implementation of kalman filter
******************************************************************************
* @attention
* 该卡尔曼滤波器可以在传感器采样频率不同的情况下，动态调整矩阵H R和K的维数与数值。
* This implementation of kalman filter can dynamically adjust dimension and
* value of matrix H R and K according to the measurement validity under any
* circumstance that the sampling rate of component sensors are different.
*
* 因此矩阵H和R的初始化会与矩阵P A和Q有所不同。另外的，在初始化量测向量z时需要额外写
* 入传感器量测所对应的状态与这个量测的方式，详情请见例程
* Therefore, the initialization of matrix P, F, and Q is sometimes different
* from that of matrices H R. when initialization. Additionally, the corresponding
* state and the method of the measurement should be provided when initializing
* measurement vector z. For more details, please see the example.
*
* 若不需要动态调整量测向量z，可简单将结构体中的Use_Auto_Adjustment初始化为0，并像初
* 始化矩阵P那样用常规方式初始化z H R即可。
* If automatic adjustment is not required, assign zero to the UseAutoAdjustment
* and initialize z H R in the normal way as matrix P.
*
* 要求量测向量z与控制向量u在传感器回调函数中更新。整数0意味着量测无效，即自上次卡尔曼
* 滤波更新后无传感器数据更新。因此量测向量z与控制向量u会在卡尔曼滤波更新过程中被清零
* MeasuredVector and ControlVector are required to be updated in the sensor
* callback function. Integer 0 in measurement vector z indicates the invalidity
* of current measurement, so MeasuredVector and ControlVector will be reset
* (to 0) during each update.
*
* 此外，矩阵P过度收敛后滤波器将难以再适应状态的缓慢变化，从而产生滤波估计偏差。该算法
* 通过限制矩阵P最小值的方法，可有效抑制滤波器的过度收敛，详情请见例程。
* Additionally, the excessive convergence of matrix P will make filter incapable
* of adopting the slowly changing state. This implementation can effectively
* suppress filter excessive convergence through boundary limiting for matrix P.
* For more details, please see the example.
*
* @example:
* x =
* | height |
* | velocity |
* |acceleration|
*
* KalmanFilter_t Height_KF;
*
* void INS_Task_Init(void)
* {
* static float P_Init[9] =
* {
* 10, 0, 0,
* 0, 30, 0,
* 0, 0, 10,
* };
* static float F_Init[9] =
* {
* 1, dt, 0.5*dt*dt,
* 0, 1, dt,
* 0, 0, 1,
* };
* static float Q_Init[9] =
* {
* 0.25*dt*dt*dt*dt, 0.5*dt*dt*dt, 0.5*dt*dt,
* 0.5*dt*dt*dt, dt*dt, dt,
* 0.5*dt*dt, dt, 1,
* };
*
* // 设置最小方差
* static float state_min_variance[3] = {0.03, 0.005, 0.1};
*
* // 开启自动调整
* Height_KF.UseAutoAdjustment = 1;
*
* // 气压测得高度 GPS测得高度 加速度计测得z轴运动加速度
* static uint8_t measurement_reference[3] = {1, 1, 3}
*
* static float measurement_degree[3] = {1, 1, 1}
* // 根据measurement_reference与measurement_degree生成H矩阵如下（在当前周期全部测量数据有效情况下）
* |1 0 0|
* |1 0 0|
* |0 0 1|
*
* static float mat_R_diagonal_elements = {30, 25, 35}
* //根据mat_R_diagonal_elements生成R矩阵如下（在当前周期全部测量数据有效情况下）
* |30 0 0|
* | 0 25 0|
* | 0 0 35|
*
* Kalman_Filter_Init(&Height_KF, 3, 0, 3);
*
* // 设置矩阵值
* memcpy(Height_KF.P_data, P_Init, sizeof(P_Init));
* memcpy(Height_KF.F_data, F_Init, sizeof(F_Init));
* memcpy(Height_KF.Q_data, Q_Init, sizeof(Q_Init));
* memcpy(Height_KF.MeasurementMap, measurement_reference, sizeof(measurement_reference));
* memcpy(Height_KF.MeasurementDegree, measurement_degree, sizeof(measurement_degree));
* memcpy(Height_KF.MatR_DiagonalElements, mat_R_diagonal_elements, sizeof(mat_R_diagonal_elements));
* memcpy(Height_KF.StateMinVariance, state_min_variance, sizeof(state_min_variance));
* }
*
* void INS_Task(void const *pvParameters)
* {
* // 循环更新
* Kalman_Filter_Update(&Height_KF);
* vTaskDelay(ts);
* }
*
* // 测量数据更新应按照以下形式 即向MeasuredVector赋值
* void Barometer_Read_Over(void)
* {
* ......
* INS_KF.MeasuredVector[0] = baro_height;
* }
* void GPS_Read_Over(void)
* {
* ......
* INS_KF.MeasuredVector[1] = GPS_height;
* }
* void Acc_Data_Process(void)
* {
* ......
* INS_KF.MeasuredVector[2] = acc.z;
* }
******************************************************************************
*/
#include "kalman_filter.h"
uint16_t sizeof_float, sizeof_double;
static void H_K_R_Adjustment(KalmanFilter_t *kf);
/**
* @brief 初始化矩阵维度信息并为矩阵分配空间
*
* @param kf kf类型定义
* @param xhatSize 状态变量维度
* @param uSize 控制变量维度
* @param zSize 观测量维度
*/
void Kalman_Filter_Init(KalmanFilter_t *kf, uint8_t xhatSize, uint8_t uSize, uint8_t zSize)
{
sizeof_float = sizeof(float);
sizeof_double = sizeof(double);
kf->xhatSize = xhatSize;
kf->uSize = uSize;
kf->zSize = zSize;
kf->MeasurementValidNum = 0;
// measurement flags
kf->MeasurementMap = (uint8_t *)user_malloc(sizeof(uint8_t) * zSize);
memset(kf->MeasurementMap, 0, sizeof(uint8_t) * zSize);
kf->MeasurementDegree = (float *)user_malloc(sizeof_float * zSize);
memset(kf->MeasurementDegree, 0, sizeof_float * zSize);
kf->MatR_DiagonalElements = (float *)user_malloc(sizeof_float * zSize);
memset(kf->MatR_DiagonalElements, 0, sizeof_float * zSize);
kf->StateMinVariance = (float *)user_malloc(sizeof_float * xhatSize);
memset(kf->StateMinVariance, 0, sizeof_float * xhatSize);
kf->temp = (uint8_t *)user_malloc(sizeof(uint8_t) * zSize);
memset(kf->temp, 0, sizeof(uint8_t) * zSize);
// filter data
kf->FilteredValue = (float *)user_malloc(sizeof_float * xhatSize);
memset(kf->FilteredValue, 0, sizeof_float * xhatSize);
kf->MeasuredVector = (float *)user_malloc(sizeof_float * zSize);
memset(kf->MeasuredVector, 0, sizeof_float * zSize);
kf->ControlVector = (float *)user_malloc(sizeof_float * uSize);
memset(kf->ControlVector, 0, sizeof_float * uSize);
// xhat x(k|k)
kf->xhat_data = (float *)user_malloc(sizeof_float * xhatSize);
memset(kf->xhat_data, 0, sizeof_float * xhatSize);
Matrix_Init(&kf->xhat, kf->xhatSize, 1, (float *)kf->xhat_data);
// xhatminus x(k|k-1)
kf->xhatminus_data = (float *)user_malloc(sizeof_float * xhatSize);
memset(kf->xhatminus_data, 0, sizeof_float * xhatSize);
Matrix_Init(&kf->xhatminus, kf->xhatSize, 1, (float *)kf->xhatminus_data);
if (uSize != 0)
{
// control vector u
kf->u_data = (float *)user_malloc(sizeof_float * uSize);
memset(kf->u_data, 0, sizeof_float * uSize);
Matrix_Init(&kf->u, kf->uSize, 1, (float *)kf->u_data);
}
// measurement vector z
kf->z_data = (float *)user_malloc(sizeof_float * zSize);
memset(kf->z_data, 0, sizeof_float * zSize);
Matrix_Init(&kf->z, kf->zSize, 1, (float *)kf->z_data);
// covariance matrix P(k|k)
kf->P_data = (float *)user_malloc(sizeof_float * xhatSize * xhatSize);
memset(kf->P_data, 0, sizeof_float * xhatSize * xhatSize);
Matrix_Init(&kf->P, kf->xhatSize, kf->xhatSize, (float *)kf->P_data);
// create covariance matrix P(k|k-1)
kf->Pminus_data = (float *)user_malloc(sizeof_float * xhatSize * xhatSize);
memset(kf->Pminus_data, 0, sizeof_float * xhatSize * xhatSize);
Matrix_Init(&kf->Pminus, kf->xhatSize, kf->xhatSize, (float *)kf->Pminus_data);
// state transition matrix F FT
kf->F_data = (float *)user_malloc(sizeof_float * xhatSize * xhatSize);
kf->FT_data = (float *)user_malloc(sizeof_float * xhatSize * xhatSize);
memset(kf->F_data, 0, sizeof_float * xhatSize * xhatSize);
memset(kf->FT_data, 0, sizeof_float * xhatSize * xhatSize);
Matrix_Init(&kf->F, kf->xhatSize, kf->xhatSize, (float *)kf->F_data);
Matrix_Init(&kf->FT, kf->xhatSize, kf->xhatSize, (float *)kf->FT_data);
if (uSize != 0)
{
// control matrix B
kf->B_data = (float *)user_malloc(sizeof_float * xhatSize * uSize);
memset(kf->B_data, 0, sizeof_float * xhatSize * uSize);
Matrix_Init(&kf->B, kf->xhatSize, kf->uSize, (float *)kf->B_data);
}
// measurement matrix H
kf->H_data = (float *)user_malloc(sizeof_float * zSize * xhatSize);
kf->HT_data = (float *)user_malloc(sizeof_float * xhatSize * zSize);
memset(kf->H_data, 0, sizeof_float * zSize * xhatSize);
memset(kf->HT_data, 0, sizeof_float * xhatSize * zSize);
Matrix_Init(&kf->H, kf->zSize, kf->xhatSize, (float *)kf->H_data);
Matrix_Init(&kf->HT, kf->xhatSize, kf->zSize, (float *)kf->HT_data);
// process noise covariance matrix Q
kf->Q_data = (float *)user_malloc(sizeof_float * xhatSize * xhatSize);
memset(kf->Q_data, 0, sizeof_float * xhatSize * xhatSize);
Matrix_Init(&kf->Q, kf->xhatSize, kf->xhatSize, (float *)kf->Q_data);
// measurement noise covariance matrix R
kf->R_data = (float *)user_malloc(sizeof_float * zSize * zSize);
memset(kf->R_data, 0, sizeof_float * zSize * zSize);
Matrix_Init(&kf->R, kf->zSize, kf->zSize, (float *)kf->R_data);
// kalman gain K
kf->K_data = (float *)user_malloc(sizeof_float * xhatSize * zSize);
memset(kf->K_data, 0, sizeof_float * xhatSize * zSize);
Matrix_Init(&kf->K, kf->xhatSize, kf->zSize, (float *)kf->K_data);
kf->S_data = (float *)user_malloc(sizeof_float * kf->xhatSize * kf->xhatSize);
kf->temp_matrix_data = (float *)user_malloc(sizeof_float * kf->xhatSize * kf->xhatSize);
kf->temp_matrix_data1 = (float *)user_malloc(sizeof_float * kf->xhatSize * kf->xhatSize);
kf->temp_vector_data = (float *)user_malloc(sizeof_float * kf->xhatSize);
kf->temp_vector_data1 = (float *)user_malloc(sizeof_float * kf->xhatSize);
Matrix_Init(&kf->S, kf->xhatSize, kf->xhatSize, (float *)kf->S_data);
Matrix_Init(&kf->temp_matrix, kf->xhatSize, kf->xhatSize, (float *)kf->temp_matrix_data);
Matrix_Init(&kf->temp_matrix1, kf->xhatSize, kf->xhatSize, (float *)kf->temp_matrix_data1);
Matrix_Init(&kf->temp_vector, kf->xhatSize, 1, (float *)kf->temp_vector_data);
Matrix_Init(&kf->temp_vector1, kf->xhatSize, 1, (float *)kf->temp_vector_data1);
kf->SkipEq1 = 0;
kf->SkipEq2 = 0;
kf->SkipEq3 = 0;
kf->SkipEq4 = 0;
kf->SkipEq5 = 0;
}
void Kalman_Filter_Measure(KalmanFilter_t *kf)
{
// 矩阵H K R根据量测情况自动调整
// matrix H K R auto adjustment
if (kf->UseAutoAdjustment != 0)
H_K_R_Adjustment(kf);
else
{
memcpy(kf->z_data, kf->MeasuredVector, sizeof_float * kf->zSize);
memset(kf->MeasuredVector, 0, sizeof_float * kf->zSize);
}
memcpy(kf->u_data, kf->ControlVector, sizeof_float * kf->uSize);
}
void Kalman_Filter_xhatMinusUpdate(KalmanFilter_t *kf)
{
if (!kf->SkipEq1)
{
if (kf->uSize > 0)
{
kf->temp_vector.numRows = kf->xhatSize;
kf->temp_vector.numCols = 1;
kf->MatStatus = Matrix_Multiply(&kf->F, &kf->xhat, &kf->temp_vector);
kf->temp_vector1.numRows = kf->xhatSize;
kf->temp_vector1.numCols = 1;
kf->MatStatus = Matrix_Multiply(&kf->B, &kf->u, &kf->temp_vector1);
kf->MatStatus = Matrix_Add(&kf->temp_vector, &kf->temp_vector1, &kf->xhatminus);
}
else
{
kf->MatStatus = Matrix_Multiply(&kf->F, &kf->xhat, &kf->xhatminus);
}
}
}
void Kalman_Filter_PminusUpdate(KalmanFilter_t *kf)
{
if (!kf->SkipEq2)
{
kf->MatStatus = Matrix_Transpose(&kf->F, &kf->FT);
kf->MatStatus = Matrix_Multiply(&kf->F, &kf->P, &kf->Pminus);
kf->temp_matrix.numRows = kf->Pminus.numRows;
kf->temp_matrix.numCols = kf->FT.numCols;
kf->MatStatus = Matrix_Multiply(&kf->Pminus, &kf->FT, &kf->temp_matrix); // temp_matrix = F P(k-1) FT
kf->MatStatus = Matrix_Add(&kf->temp_matrix, &kf->Q, &kf->Pminus);
}
}
void Kalman_Filter_SetK(KalmanFilter_t *kf)
{
if (!kf->SkipEq3)
{
kf->MatStatus = Matrix_Transpose(&kf->H, &kf->HT); // z|x => x|z
kf->temp_matrix.numRows = kf->H.numRows;
kf->temp_matrix.numCols = kf->Pminus.numCols;
kf->MatStatus = Matrix_Multiply(&kf->H, &kf->Pminus, &kf->temp_matrix); // temp_matrix = H·P'(k)
kf->temp_matrix1.numRows = kf->temp_matrix.numRows;
kf->temp_matrix1.numCols = kf->HT.numCols;
kf->MatStatus = Matrix_Multiply(&kf->temp_matrix, &kf->HT, &kf->temp_matrix1); // temp_matrix1 = H·P'(k)·HT
kf->S.numRows = kf->R.numRows;
kf->S.numCols = kf->R.numCols;
kf->MatStatus = Matrix_Add(&kf->temp_matrix1, &kf->R, &kf->S); // S = H P'(k) HT + R
kf->MatStatus = Matrix_Inverse(&kf->S, &kf->temp_matrix1); // temp_matrix1 = inv(H·P'(k)·HT + R)
kf->temp_matrix.numRows = kf->Pminus.numRows;
kf->temp_matrix.numCols = kf->HT.numCols;
kf->MatStatus = Matrix_Multiply(&kf->Pminus, &kf->HT, &kf->temp_matrix); // temp_matrix = P'(k)·HT
kf->MatStatus = Matrix_Multiply(&kf->temp_matrix, &kf->temp_matrix1, &kf->K);
}
}
void Kalman_Filter_xhatUpdate(KalmanFilter_t *kf)
{
if (!kf->SkipEq4)
{
kf->temp_vector.numRows = kf->H.numRows;
kf->temp_vector.numCols = 1;
kf->MatStatus = Matrix_Multiply(&kf->H, &kf->xhatminus, &kf->temp_vector); // temp_vector = H xhat'(k)
kf->temp_vector1.numRows = kf->z.numRows;
kf->temp_vector1.numCols = 1;
kf->MatStatus = Matrix_Subtract(&kf->z, &kf->temp_vector, &kf->temp_vector1); // temp_vector1 = z(k) - H·xhat'(k)
kf->temp_vector.numRows = kf->K.numRows;
kf->temp_vector.numCols = 1;
kf->MatStatus = Matrix_Multiply(&kf->K, &kf->temp_vector1, &kf->temp_vector); // temp_vector = K(k)·(z(k) - H·xhat'(k))
kf->MatStatus = Matrix_Add(&kf->xhatminus, &kf->temp_vector, &kf->xhat);
}
}
void Kalman_Filter_P_Update(KalmanFilter_t *kf)
{
if (!kf->SkipEq5)
{
kf->temp_matrix.numRows = kf->K.numRows;
kf->temp_matrix.numCols = kf->H.numCols;
kf->temp_matrix1.numRows = kf->temp_matrix.numRows;
kf->temp_matrix1.numCols = kf->Pminus.numCols;
kf->MatStatus = Matrix_Multiply(&kf->K, &kf->H, &kf->temp_matrix); // temp_matrix = K(k)·H
kf->MatStatus = Matrix_Multiply(&kf->temp_matrix, &kf->Pminus, &kf->temp_matrix1); // temp_matrix1 = K(k)·H·P'(k)
kf->MatStatus = Matrix_Subtract(&kf->Pminus, &kf->temp_matrix1, &kf->P);
}
}
/**
* @brief 执行卡尔曼滤波黄金五式,提供了用户定义函数,可以替代五个中的任意一个环节,方便自行扩展为EKF/UKF/ESKF/AUKF等
*
* @param kf kf类型定义
* @return float* 返回滤波值
*/
float *Kalman_Filter_Update(KalmanFilter_t *kf)
{
// 0. 获取量测信息
Kalman_Filter_Measure(kf);
if (kf->User_Func0_f != NULL)
kf->User_Func0_f(kf);
// 先验估计
// 1. xhat'(k)= A·xhat(k-1) + B·u
Kalman_Filter_xhatMinusUpdate(kf);
if (kf->User_Func1_f != NULL)
kf->User_Func1_f(kf);
// 预测更新
// 2. P'(k) = A·P(k-1)·AT + Q
Kalman_Filter_PminusUpdate(kf);
if (kf->User_Func2_f != NULL)
kf->User_Func2_f(kf);
if (kf->MeasurementValidNum != 0 || kf->UseAutoAdjustment == 0)
{
// 量测更新
// 3. K(k) = P'(k)·HT / (H·P'(k)·HT + R)
Kalman_Filter_SetK(kf);
if (kf->User_Func3_f != NULL)
kf->User_Func3_f(kf);
// 融合
// 4. xhat(k) = xhat'(k) + K(k)·(z(k) - H·xhat'(k))
Kalman_Filter_xhatUpdate(kf);
if (kf->User_Func4_f != NULL)
kf->User_Func4_f(kf);
// 修正方差
// 5. P(k) = (1-K(k)·H)·P'(k) ==> P(k) = P'(k)-K(k)·H·P'(k)
Kalman_Filter_P_Update(kf);
}
else
{
// 无有效量测,仅预测
// xhat(k) = xhat'(k)
// P(k) = P'(k)
memcpy(kf->xhat_data, kf->xhatminus_data, sizeof_float * kf->xhatSize);
memcpy(kf->P_data, kf->Pminus_data, sizeof_float * kf->xhatSize * kf->xhatSize);
}
// 自定义函数,可以提供后处理等
if (kf->User_Func5_f != NULL)
kf->User_Func5_f(kf);
// 避免滤波器过度收敛
// suppress filter excessive convergence
for (uint8_t i = 0; i < kf->xhatSize; i++)
{
if (kf->P_data[i * kf->xhatSize + i] < kf->StateMinVariance[i])
kf->P_data[i * kf->xhatSize + i] = kf->StateMinVariance[i];
}
memcpy(kf->FilteredValue, kf->xhat_data, sizeof_float * kf->xhatSize);
if (kf->User_Func6_f != NULL)
kf->User_Func6_f(kf);
return kf->FilteredValue;
}
static void H_K_R_Adjustment(KalmanFilter_t *kf)
{
kf->MeasurementValidNum = 0;
memcpy(kf->z_data, kf->MeasuredVector, sizeof_float * kf->zSize);
memset(kf->MeasuredVector, 0, sizeof_float * kf->zSize);
// 识别量测数据有效性并调整矩阵H R K
// recognize measurement validity and adjust matrices H R K
memset(kf->R_data, 0, sizeof_float * kf->zSize * kf->zSize);
memset(kf->H_data, 0, sizeof_float * kf->xhatSize * kf->zSize);
for (uint8_t i = 0; i < kf->zSize; i++)
{
if (kf->z_data[i] != 0)
{
// 重构向量z
// rebuild vector z
kf->z_data[kf->MeasurementValidNum] = kf->z_data[i];
kf->temp[kf->MeasurementValidNum] = i;
// 重构矩阵H
// rebuild matrix H
kf->H_data[kf->xhatSize * kf->MeasurementValidNum + kf->MeasurementMap[i] - 1] = kf->MeasurementDegree[i];
kf->MeasurementValidNum++;
}
}
for (uint8_t i = 0; i < kf->MeasurementValidNum; i++)
{
// 重构矩阵R
// rebuild matrix R
kf->R_data[i * kf->MeasurementValidNum + i] = kf->MatR_DiagonalElements[kf->temp[i]];
}
// 调整矩阵维数
// adjust the dimensions of system matrices
kf->H.numRows = kf->MeasurementValidNum;
kf->H.numCols = kf->xhatSize;
kf->HT.numRows = kf->xhatSize;
kf->HT.numCols = kf->MeasurementValidNum;
kf->R.numRows = kf->MeasurementValidNum;
kf->R.numCols = kf->MeasurementValidNum;
kf->K.numRows = kf->xhatSize;
kf->K.numCols = kf->MeasurementValidNum;
kf->z.numRows = kf->MeasurementValidNum;
}
云台/modules/imu/qekf/kalman_filter.h
+121
View File
@@ -0,0 +1,121 @@
/**
******************************************************************************
* @file kalman filter.h
* @author Wang Hongxi
* @version V1.2.2
* @date 2022/1/8
* @brief
******************************************************************************
* @attention
*
******************************************************************************
*/
#ifndef __KALMAN_FILTER_H
#define __KALMAN_FILTER_H
// cortex-m4 DSP lib
/*
#define __CC_ARM // Keil
#define ARM_MATH_CM4
#define ARM_MATH_MATRIX_CHECK
#define ARM_MATH_ROUNDING
#define ARM_MATH_DSP // define in arm_math.h
*/
#include "stm32f407xx.h"
#include "arm_math.h"
//#include "dsp/matrix_functions.h"
#include "math.h"
#include "stdint.h"
#include "stdlib.h"
#ifndef user_malloc
#ifdef _CMSIS_OS_H
#define user_malloc pvPortMalloc
#else
#define user_malloc malloc
#endif
#endif
#define mat arm_matrix_instance_f32
#define Matrix_Init arm_mat_init_f32
#define Matrix_Add arm_mat_add_f32
#define Matrix_Subtract arm_mat_sub_f32
#define Matrix_Multiply arm_mat_mult_f32
#define Matrix_Transpose arm_mat_trans_f32
#define Matrix_Inverse arm_mat_inverse_f32
typedef struct kf_t
{
float *FilteredValue;
float *MeasuredVector;
float *ControlVector;
uint8_t xhatSize;
uint8_t uSize;
uint8_t zSize;
uint8_t UseAutoAdjustment;
uint8_t MeasurementValidNum;
uint8_t *MeasurementMap; // 量测与状态的关系 how measurement relates to the state
float *MeasurementDegree; // 测量值对应H矩阵元素值 elements of each measurement in H
float *MatR_DiagonalElements; // 量测方差 variance for each measurement
float *StateMinVariance; // 最小方差 避免方差过度收敛 suppress filter excessive convergence
uint8_t *temp;
// 配合用户定义函数使用,作为标志位用于判断是否要跳过标准KF中五个环节中的任意一个
uint8_t SkipEq1, SkipEq2, SkipEq3, SkipEq4, SkipEq5;
// definiion of struct mat: rows & cols & pointer to vars
mat xhat; // x(k|k)
mat xhatminus; // x(k|k-1)
mat u; // control vector u
mat z; // measurement vector z
mat P; // covariance matrix P(k|k)
mat Pminus; // covariance matrix P(k|k-1)
mat F, FT; // state transition matrix F FT
mat B; // control matrix B
mat H, HT; // measurement matrix H
mat Q; // process noise covariance matrix Q
mat R; // measurement noise covariance matrix R
mat K; // kalman gain K
mat S, temp_matrix, temp_matrix1, temp_vector, temp_vector1;
int8_t MatStatus;
// 用户定义函数,可以替换或扩展基准KF的功能
void (*User_Func0_f)(struct kf_t *kf);
void (*User_Func1_f)(struct kf_t *kf);
void (*User_Func2_f)(struct kf_t *kf);
void (*User_Func3_f)(struct kf_t *kf);
void (*User_Func4_f)(struct kf_t *kf);
void (*User_Func5_f)(struct kf_t *kf);
void (*User_Func6_f)(struct kf_t *kf);
// 矩阵存储空间指针
float *xhat_data, *xhatminus_data;
float *u_data;
float *z_data;
float *P_data, *Pminus_data;
float *F_data, *FT_data;
float *B_data;
float *H_data, *HT_data;
float *Q_data;
float *R_data;
float *K_data;
float *S_data, *temp_matrix_data, *temp_matrix_data1, *temp_vector_data, *temp_vector_data1;
} KalmanFilter_t;
extern uint16_t sizeof_float, sizeof_double;
void Kalman_Filter_Init(KalmanFilter_t *kf, uint8_t xhatSize, uint8_t uSize, uint8_t zSize);
void Kalman_Filter_Measure(KalmanFilter_t *kf);
void Kalman_Filter_xhatMinusUpdate(KalmanFilter_t *kf);
void Kalman_Filter_PminusUpdate(KalmanFilter_t *kf);
void Kalman_Filter_SetK(KalmanFilter_t *kf);
void Kalman_Filter_xhatUpdate(KalmanFilter_t *kf);
void Kalman_Filter_P_Update(KalmanFilter_t *kf);
float *Kalman_Filter_Update(KalmanFilter_t *kf);
#endif //__KALMAN_FILTER_H